Every technician is IICRC certified and has handled hardwood floor water damage many times. You get a clear plan before any work starts.
The sooner drying starts, the less there is to repair. Our phones are answered around the clock, with same-day visits when available.
Filing a claim is easier with good records. We document everything and talk to your adjuster for you.
Most people who call us have never dealt with hardwood floor water damage before. We walk you through it on the phone, then send a local crew with the right equipment.
It does not take long for water to change a wood floor. As the wood absorbs water along its edges and bottom face, it expands, crowds the neighboring boards and cups, leaving the center lower than the sides. Cupping alone is no reason to give up on the floor. Boards of solid wood often return to flat if they are dried during those early days. Success depends on a slow, even drying rate that draws water from the flooring and from the subfloor beneath it.
Our tool for hardwood is the floor drying mat. The mats are sealed to the surface and connected to a vacuum unit that draws moisture up through the boards and seams, while dehumidifiers keep the room air dry. Compared with carpet or drywall it is slower, commonly a week or more. Hold off on the sander until every board is fully dry. Sand a cupped floor too soon and it will crown later.
Seams let the water through, and it fans out in the layer between flooring and subfloor. The surface may wipe dry while the underside stays soaked.
Boards swell and the edges rise. You might notice haze in the topcoat. Mold can begin on the subfloor and the unfinished underside of the wood.
Expanding boards push harder and harder on one another. With fasteners losing their hold and boards compressing at the edges, some areas can lift away from the subfloor.
Buckling, black staining and mold under the boards become likely. Drying is usually no longer enough, and the bulk of the wet flooring has to be replaced.
Readings are taken in the boards and the subfloor, and on dry flooring close by as a reference. That tells us how deep the water went and whether saving the floor is realistic.
Standing water is extracted right away and rugs and furniture are moved off the wet area. Boards swell less when the seams stop taking in water sooner.
Floor mats are taped down and connected to a vacuum system that pulls moisture up through the boards. Dehumidifiers control the room so the wood dries evenly without cracking.
Every day or two we take new readings, continuing until the subfloor and boards match the dry reference spots. Our final advice is one of three outcomes, no further work, swapping a few boards, or refinishing the floor.
Lingering moisture rusts the fasteners, which then hold the boards less firmly. The rust also bleeds into the wood as dark stains that sanding may not remove.
Long after the boards seem dry, the subfloor may still be holding water. Unless that layer is dried as well, expect renewed cupping or mold on the underside.
Between the boards and the subfloor there is only darkness and still air. Mold in that layer cannot be seen from the room, and a musty odor is usually the first sign.
When the top of the wood dries much quicker than the inside, stress builds in the board. Lasting gaps and split or cracked boards are the usual outcome.
It depends on the material, how long it stayed wet and how clean the water was. We test before we decide, and we tell you why.
Ask a Tech: (720) 208-4006| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Solid hardwood | Flooring still attached with cupping only, and drying begun in days | Boards that buckled, cracked or turned black, plus anything touched by sewage |
| Paper or felt underlayment | Paper underlayment left in place when the floor dries flat | Any paper or felt under removed flooring, and all moldy sections |
| Plywood subfloor | Flat, solid panels that dry back to normal readings | Panels with visible mold, softness or plies coming apart |
| OSB or particle board | Only OSB showing no edge swell | Swollen OSB and nearly any wet particle board |
| Engineered hardwood | Brief surface water with no swelling at the edges | Swollen planks, layers coming apart, or moisture below them |
Not seeing your question? Call and ask. It costs nothing to talk it through.
Call (720) 208-4006Don't wait for small problems to become expensive emergencies. Call Carlsbad Restoration for fast, reliable service.
Call (720) 208-4006 Now