Every technician is IICRC certified and has handled wall and drywall water damage many times. You get a clear plan before any work starts.
You get a straight answer on cost up front, with every line explained and nothing hidden.
You focus on your home. We put together the photos, readings and reports your insurance company needs.
You do not have to work out how bad it is on your own. Call, tell us what you see, and a Carlsbad technician will explain the next step and what it should cost.
A sheet of drywall behaves much as a wick does. Once the base of a wall gets wet, moisture climbs through the paper and gypsum, commonly a foot or more higher than the water stood on the floor. From the room, the surface may seem dry and sound even though the hidden face and the insulation are saturated. That is why we check walls with a moisture meter instead of trusting how they look.
Not every wet wall has to be torn out. Drywall that got wet with clean water and is still firm can often be dried in place, sometimes by removing the baseboard and moving air through small holes into the cavity. If the drywall has gone soft, crumbles, shows mold or took in dirty water, we do a flood cut, meaning a level cut over the damaged area with all material beneath it removed.
It depends on the material, how long it stayed wet and how clean the water was. We test before we decide, and we tell you why.
Call (720) 208-4006| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Drywall | Panels that stay hard and true after a short clean water event | Soft, swollen, moldy, or wet from gray or black water |
| Paint and wallpaper | Finish still tight to the drywall, needing only a fresh coat | Wall coverings that seal water in, plus bubbled or flaking paint |
| Wall insulation | Foam with closed cells, since moisture cannot soak into it | Fiberglass and cellulose that got wet, because they slump and hold moisture |
| Plaster walls | Sections still solid and attached when the moisture is gone | Spots gone chalky or soft, or pulling off the lath |
| Baseboards and trim | Wood baseboards with no warp or splits once dry | Swollen MDF and trim with edges that are flaking apart |
Water in a perimeter wall may reach the sheathing on the far side of the cavity. It gets a moisture reading prior to closing, since it holds dampness a long time.
Outlets and wiring are mounted near the floor, exactly where the water gathers. Until that circuit is inspected, avoid plugging anything into the affected wall.
Batts of fiberglass absorb water and keep it pressed to the framing. No amount of airflow on the painted side will dry a cavity packed with wet batts.
Wet drywall behind cabinets, vanities and built-ins gets no airflow and is easy to overlook. We take readings through toe kicks and from the opposite side to find it.
We scan each wall with a moisture meter and thermal camera and mark how high and how far the water traveled, including the opposite side and adjoining rooms.
Based on the water category, how long it sat and how the drywall feels, we tell you plainly which sections can be dried in place and which need to come out.
Walls we are keeping have their baseboards removed so air can be pushed into the cavity. Walls that cannot be kept get a flood cut along a level line, with the wet insulation pulled.
Dehumidifiers and air movers stay on, usually 3 to 5 days, until the studs and the drywall left in place test dry. The rebuild follows with fresh insulation, drywall installation and finishing, trim and a coat of paint.
Moisture enters where the panel meets the floor and wicks upward from there. Baseboards and the bottom plate take on moisture.
The wet line rises higher, baseboards swell and paint begins to blister. Mold can start on the paper facing inside the cavity.
Gypsum softens and the paper lets go. A musty odor grows stronger while the batts settle and mold covers more of the unseen face.
Studs and plates stay wet long enough to grow mold and begin to decay. Much more wall now has to be removed and rebuilt.
Not seeing your question? Call and ask. It costs nothing to talk it through.
Call (720) 208-4006Take action now and prevent costly damage. Carlsbad Restoration is ready to help.
Call (720) 208-4006 Now